Daedalus DS-808 M AC – Manual Pushable Scissor Lift with 8m Working Height

Introduction

DAEDALUS® Manual Pushable Scissor Lifts are an Economical Worksite solution without any compromise on the machine’s safety. These scissor lifts are Manually Maneuverable while their raising & lowering operations can be performed by AC / Battery Power Source as per your requirement. These machines are equipped with Pull out Screw Jack Stabilizers that enable them to level the machines. The solid Tyres on these machines enable you to utilize these machines in all conditions. These machines exhibit Least Downtime and require Minimum maintenance, thus enhancing your onsite Productivity.

Features:

1. Optional Power Source (AC / Battery Pack)
2. Anti-Skid Platform.
3. Foldable Guardrails (Optional).
4. Dual Control
5. Forklift Pockets

Safety Systems:

1. Manual Stabilizers
2. Max. Height cut off Switch
3. Flashing Beacon
4. Manual emergency relief valve

Specification

Models		DS-808M/AC
Measurements		Feet	Metric
Maximum Working Height*		26ft	8m
Maximum Platform Height		20ft	6m
Lowered Platform Height		4.5ft	1.4m
Platform Length -		6.9ft	2.1m
Platform Width		3.9ft	2.1m
Guardrail Height		3.2ft	1.0m
Vehicle Dimensions	Length	8.2ft	2.4m
	Height	6.9ft	2.15m
	Width	3.9ft	1.2m
Ground Clearence		0.3ft	90mm

Productivity

Maximum Occupancy	2 People
Lift Capacity	350Kgs
Control	Dual Control (Chassis & Platform)
Drive	NA

Power

Power Source	24V DC (Four 6V 225Ah Batteries) / 230V 50Hz Single Phase Supply
Hydraulic Capacity	20L (5.2gal)
Weight***	1800Kgs/1500Kgs

Benefits of the DS-808 M/AC

▸ 8m Working Height - The Practical Choice for Most Industrial Maintenance Tasks

The majority of factory bays, warehouse mezzanines, and commercial facilities in India have ceiling heights between 6m and 9m. The DS-808 M/AC's 8m working height (6m platform height) covers this range without the added weight, cost, or complexity of a self-propelled machine. It is a practical first-choice machine for general maintenance programmes where a powered drive system is not required.

▸ AC and Battery Dual Power - Flexible Across Site Conditions

he DS-808 M/AC runs on either 230V single-phase AC or a 24V DC battery pack, giving you the freedom to choose the power source that suits the site. Plug into mains on factory floors and commercial buildings; switch to battery in areas without accessible sockets or where trailing cables are a trip hazard. No separate generator is needed for either mode.

▸ 350 kg Capacity with 2.1m x 1.2m Platform

The platform accommodates two operators plus a working load to a combined 350 kg - the same rating as Daedalus's full-size self-propelled range. The 2.1m platform length provides enough space for both a person and a reasonable material load (light fittings, cable drums, HVAC components) without requiring multiple trips to complete the task.

▸ Screw-Jack Stabilisers for Confident Elevation on Imperfect Floors

Before raising the platform, the operator deploys four pull-out screw-jack stabilisers that level and lock the machine in place. This is particularly important in older industrial buildings where floor surfaces are uneven or sloped. The stabilisers prevent any rocking or lateral movement while work is being carried out at height.

▸ CE Certified to EN 280 - Supports Your Risk Assessment and Compliance Documentation

The DS-808 M is CE certified to EN 280. For EHS managers preparing working-at-height risk assessments, this means the machine's structural and safety performance has been independently verified against an internationally recognised standard. It supports compliance with India's Factories Act 1948 and IS 3521 requirements without the need for additional in-house testing or certification.

▸ Manual Height Cut-Off Switch - Automatic Protection at Rated Height

A mechanical height cut-off switch prevents the platform from being raised beyond its rated working height, regardless of operator input. This is a simple but important safety device that eliminates the risk of accidental over-extension - particularly relevant when less-experienced operators are using the machine.

▸ Simple to Relocate - No Drive Licence or Operator Certification Complexity

Because the DS-808 M/AC is manually pushed rather than self-propelled, repositioning between tasks does not require a separate machine travel assessment or the additional competency requirements associated with driven

MEWPs. Maintenance teams can move the machine between work locations without additional procedure overhead.

FAQs